Looking for:
Innova.com manuals |
Innova Pro - Downloads - Diagnostics Made Easy.Innova.com manuals
Description.Innova.com manuals
Hide thumbs. Table Of Contents. Quick Links. Table of Contents. Previous Page. Next Page. Diagnostic Equipment Innova Manual Fuel injection pressure tester kit 48 pages. This manual describes common test procedures used by experienced service technicians. Always read your vehicle's service manual and follow its safety precautions before and during any test or service procedure. Controls and Indicators See Figure 1 for the locations of items 1 through 7, below. Headphone port — Supports connection of external headphones.
Display - Color LCD display shows menus and submenus, test results, tablet functions and vehicle status information. The on-board computer is the heart of the Computer Control System.
The emission checks being conducted at the time were not performed under simulated driving conditions. These conditions may include starting the vehicle when it is cold, driving the vehicle at a steady speed cruising , accelerating, etc.
The Federal Government does not require vehicle manufacturers to go beyond the standardized generic DTCs in order to comply with the new OBD2 emissions standards. Fuel Trim is a set of positive and negative values that represent adding or subtracting fuel from the engine. In this case, the monitor fails the test. If a fault is found on the first trip, the computer temporarily saves the fault in its memory as a Pending Code. The EVAP Monitor checks for proper fuel vapor flow to the engine, and pressurizes the system to test for leaks.
A faulty oxygen sensor reacts slowly, or its voltage signal is weak or missing. NOx Aftertreatment is designed to reduce oxides of nitrogen emitted in the exhaust stream. The zeolite acts as a molecular "sponge" The filter has a honeycomb structure similar to a catalyst substrate, but with the channels blocked at alternate ends.
This forces the exhaust gas to flow through the walls between the channels, filtering the particulate matter out. Turn the ignition off. Turn the ignition ON. DO NOT start the engine. Tap Global OBD. Each entry in the list include the DTC number and description. The issue of the vehicle being ready for an Emissions Test will depend on the emissions regulations and laws of your local area. Some areas require that all Monitors indicate a "Has Run" Tap the View Drive Cycles button view Drive The Next Service field shows the odometer reading at which the associated service procedures are due.
Tap the Create Report! Tap Vehicle Diagnostics. The Vehicle Diagnostics screen displays. Refer to the appropriate paragraph for the diagnostic procedure you wish to perform: Network Scan — The specific tests available depend on the vehicle make and model. Tap the appropriate control to operate the actuator as desired. The screen refreshes to show the result. Repeat step 5 as desired. Tap Back to return to the Actuator Test menu.
Performing Special Tests for a Selected Module Special Tests let you perform diagnostic and calibration procedures for various vehicle actuators and systems. Follow the on-screen prompts to prepare the vehicle for testing, and to perform the selected test procedure.
Tap Finish or Exit to return to the previous menu. You may also choose to record Live Data for later viewing. See Recording Capturing Live Data on page 45 for details.
Tap a monitor name to view the Drive Cycle procedure for the selected monitor. Two values are returned for each monitor; the number of times that all conditions necessary for a specific monitor to detect a malfunction have been encountered XXXCOND , and the number of times that the vehicle has been operated under the specific conditions for the monitor XXXCOMP.
Tap Battery Reset Procedures. The Battery Reset Procedures menu displays. Tap Reset Battery Monitoring System. Follow the instructions provided to prepare the vehicle for battery reset OBD service.
When all necessary procedures have been performed, tap Next to continue. For some vehicles, one or more submenus display. Proceed to step 2. Tap Exit to return to the Service Reset screen. Tap OK to return to the Service Reset screen. Tap Next, as appropriate, to scroll to the next screen.
You can perform a battery check only, or an alternator system battery and alternator check. If battery voltage is less than Start and warm the engine to normal operating temperature. Turn on the headlights. Tap Continue to proceed. Press the accelerator pedal to raise engine speed to RPM, and maintain the engine speed. While linked to the vehicle, start the engine. Tap the Send button to send your email to Innova Technical Support.
To cancel your message without sending, tap Cancel to return to the Technical Support dialog. Tap Report An Issue. The Report an Issue page displays.
An instructional dialog displays. Page 69 4. When all data elements have been configured as desired, tap Save Settings to save your changes. A confirmation message displays. Tap Send to send your email to Innova Technical Support. To specify the current time: Tap the time format field. Swipe up or down to scroll to the desired Wi-Fi network, then tap the network name. Scroll the Settings page to the Language field. Tap the currently active language to display the Select Language menu.
Select the radio button for the desired language, then tap OK. Tap Make to display the Select Make menu. Select the radio button for the desired vehicle manufacturer, then tap OK 3. Tap Year to display the Select Year menu.
Page 76 Notes Web: www. Print page 1 Print document 79 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Upload from URL.
Comments
Post a Comment